
I’ve wanted a mason jar lamp for a while now. I don’t know when they became hip, but I’ve been wanting to make one for over a year. I never found the time (or the supplies) to make one, until now! And, of course, I had to write a tutorial about it!
Making a mason jar lamp isn’t hard at all. You don’t even need any special tools or equipment. The only thing that might hold you back a bit, is that it isn’t really cheap. I had to order my supplies online. I ordered my brightly coloured fabric cable first, thinking I’d find the fittings for the bulb cheaper in my local hardware store. Alas, this wasn’t the case and I had to order a second time.
Make sure you read through the whole tutorial in order to understand everything before you start making your jar lamp. It’ll make things a lot easier (and safer)!
So, what do you need to make a mason jar lamp?
- A mason jar – I bought min, cheaply, in the Casa
- Electrical wire – I bought brightly coloured fabric cable
- A fitting for you lamp
- A light switch (optional, you can also make a lamp without the switch, but you can never leave it plugged in, which wasn’t an option for me as our sockets aren’t easy to reach)
- An electrical plug
- A pull relief + a nut
- A black plastic pull relief
- Screwdriver
- Hammer + a nail
- Utility knife
(ps: Sorry if I made a mistake translating the technical terms above. Please correct me if any of them are wrong.)
Making an opening in the lid
Making an opening in the lid of the jar so the fitting of the lamp can be put through is the first thing you’ll need to do. You don’t need any fancy tools for this (but if you have them laying around, good for you). I used a nail, a hammer and a (heavy) utility knife.
You start by putting the lamp fitting on the lid, placing it in the middle and drawing a circle around it. I used pencil for this, because I didn’t want it to be visible afterwards. Then you use your nail and hammer to make little holes in the lid, following the circle.
When you’re done hammering away, it’s time for the tricky party. Use your heavy utility knife to cut in between the holes you just made, cutting through the little pieces the connect everything together. Take your time for this and, please be careful! Both the utility knife and the ragged parts of the lid are sharp! I managed to do this twice without cutting or scratching myself, so can you.
Connecting the fitting and the electrical wire
The photo above shows all the pieces in the right order. The cylindrical part of the fitting needs to be put into the lid obviously, but I couldn’t put it together yet. I did forget to put the piece next to the hammer (at the top of the photo) in the line, but it needs to be put between the lid and the part of the fitting where the wires go into.
Stripping fabric cable isn’t hard, but you need to keep a couple of things in mind.
- The fabric part of the cable tend to fray easily. It also creeps up. So it’s important you put a bit of tape around it before you start cutting (see photo above and below). I place the piece of tape where I thought the pull relief of the lamp would be.
- You need to make sure the copper wires from the two different parts of the cable don’t touch anywhere! When you stripped part of the cable, cut too far and see the cable peeping through the brown and blue plastic: put a bit of electrical tape on it to make sure you don’t short circuit your lamp.
For starters we strip a piece of the wire. First cut away the fabric around the wire. Make sure you taped off part of the cable before you start! I used a utility knife for stripping the wires. Carefully cut away a part of the white wire. Try not to cut into the brown and blue plastic, otherwise you have to strip more of the white plastic.
Next strip away a shorter piece of both the brown and blue piece of the wire, to get to the copper wires inside.
Put the electrical cable through the pull relief and the nut (you can screw the nut onto the pull relief immediately) ad then put the wire through the opening at the top of the fitting. Now you can secure the copper cables to the contact plate by putting each wire through a separate opening. On each of these openings there is a little screw. With the wire in place start screwing the screws in place. Make sure the part with the screws faces upwards in your fitting (the other part is where the lamp needs to connect, this should face down when you put the fitting up).
When the cable and the fitting are connected you only have to screw the cylindrical part of the fitting onto the rest of the fitting. Also screw on the lid of the fitting (remember the part next to the hammer couple of photos ago). Next put the fitting through the whole in the lid of the jar. This may take some blunt force and once it’s in, it might not come out again, so make sure everything is put together right before doing this.
Now you only have to screw the lid of the fitting down to to lid of the jar and you’re ready with the first part of your lamp!
Attaching the switch to the mason jar lamp
Adding a switch is optional, but I really wanted one. It’s also the only part in making a lamp where you can screw up big time (although, I did put the fitting together completely wrong the first time I made a lamp, but that might have been just me).
Start by unscrewing the screws of the switch. Make sure you don’t loose any of the screws. Determinate where you want your switch on your cable. You can always take your lamp with you to where you want to place it in your house to get a better idea of the ideal placement of the switch. Whenever you’ve decided cut the wire in two. Strip both sides of the wire (same as explained before).
Place the wire into the switch. Now pay attention, because the wires need to line up correctly! Blue needs to line up with blue and brown with brown. Screw the screws shut and put the switch back together.
Putting the plug on the electrical wire
Putting together the plug is the same as putting together the fitting and the switch. The precise way of putting it together depends on which kind of plug you’ve bought. I used a really simple model. I only needed to put my cable into the “mouth” of the plug, put the copper parts in two small tubes and wrap the shell around the inner part. It was very quick and easy.
And then came the nerve wrecking part: putting the lamp on for the first time! Luckily it worked. 🙂
I made a big jar lamp and a smaller mason jar lamp. Although I really like the way they look together, I’m not going to keep them together. The small lamp will live on the bookshelves and I’m going to put the big one up next to our sofa, it’ll be hanging of the ceiling as a reading lamp. That’s why I bought that extra pull relief, this way I can secure the lamp easily on the ceiling.
So, do you like my mason jar lamps? Would you make one yourself?

Ik wou al heel lang een bokaallamp maken. Ik heb geen idee wanneer ik zo’n lamp voor het eerst zag, maar ik denk dat het meer dan een jaar geleden is. Tot nu toe had ik nooit de tijd (of de materialen) om er eentje te maken, maar nu heb ik twee prachtige bokaallampen staan! En natuurlijk moest ik er een tutorial over schrijven.
Een bokaallamp maken is helemaal niet zo moeilijk, zelfs als je helemaal van nul wilt beginnen, zoals ik gedaan heb. Je hebt er ook geen speciaal gereedschap voor nodig. De prijs per bokaallamp hangt vooral af van hoeveel meter strijkijzersnoer per lamp je wil gebruiken. Ik kocht al mijn onderdelen online, aangezien ik moeite had met het vinden van de juiste stukken in de doe-het-zelf.
Vooraleer je aan je eigen lamp begint: lees de hele tutorial eerst eens goed door, zodat je alles begrijpt voor je er aan begint. Het gaat het hele proces een stuk makkelijker (en veiliger) maken!
Wat heb je allemaal nodig voor een bokaallamp?
- Een bokaal – de mijne komt van bij Casa, waar ze in verschillende maten voor weinig geld te vinden zijn (ik had eerst eentje van een oude pot erwtjes, maar die was bij nader inzien te klein)
- Elektrisch snoer – ik ging voor vrolijk gekleurd strijkijzersnoer
- Een fitting voor je lamp – de mijne is een E27, de grootste maat
- Een schakelaar – anders moet je je lamp altijd uit het stopcontact halen, wat gezien de locatie van onze stopcontacten geen optie was
- Een stekker
- Een trekontlasting + een moer
- Een ophang oog – als je hiernaar vraagt in de doe-het-zelf zeggen ze dat het niet bestaat
- Een hamer + een nagel(tje)
- Schroevendraaier (een platte, een kruis en een hele kleine)
- Een (zwaar) breekmes
Een gat in je deksel maken
Een opening in het deksel maken zodat de fitting van de lamp er door kan, is de eerste stap om een lamp te maken. Hiervoor heb je geen fancy gereedschap nodig (maar als je het hebt, des te gemakkelijker voor jou natuurlijk). Ik moest me behelpen met een nagel, een hamer en een breekmes. En dat ging ook.
Om te beginnen teken je de omtrek van je fitting op je deksel. Ik deed dit met potlood, want ik wou niet dat er achteraf iets van stift zichtbaar zou zijn. Daarna sla je om de paar mm een gat in het deksel.
Wanneer je helemaal rond bent, komt het prutswerk. Zoek een zwaar breekmes en snijdt ermee door de verbindingsstukjes tussen de gaatjes in het deksel. Hierbij wel voorzichtig zijn, want zowel het breekmes als het deksel is scherp! Ik kon het alleszins twee keer zonder mijn hand open te halen.
De fitting en de elektrische draad verbinden
Op bovenstaande foto heb ik alle stukjes die aan elkaar moeten op volgorde gelegd. Het cilindervormige stuk helemaal links moet natuurlijk in het deksel en niet er gewoon onder. Bovenaan de foto (naast de hamer) ligt er nog een stukje van mijn fitting dat als afsluiting dient, zodat het geheel mooier oogt. Dat moet eigenlijk ook nog in het rijtje rechts naast het deksel liggen.
Wanneer je het strijkijzersnoer wilt strippen om de koperen draadjes bloot te leggen, zijn er een aantal dingen die je moet onthouden:
- het stoffen omhulsel van het snoer heeft de neiging om naar boven te kruipen en om helemaal uit te vezelen wanneer je er een stukje afknipt. Om dit te voorkomen doe je best een stuk tape rond je snoer op de hoogte waar je denkt dat de trekontlaster gaat komen.
- Zorg ervoor dat de koperen draadjes uit het blauwe en bruine gedeelte elkaar nergens kunnen raken. Als je ergens een sneetje in de plastiek gemaakt hebt waar het koper door piept, kan je er wat elektrische tape rond doen om te voorkomen dat er kortsluiting kan ontstaan.
We beginnen met het strijkijzer snoer een stukje te strippen, zodat je de koperen draadjes in de lamp fitting kan vast maken. Het snoer strippen heb ik heel voorzichtig met een breekmes gedaan. Eerst moet je het stoffen omhulsel en het dikke witte plastiek van het snoer verwijderen. Voorzichtig bij dat laatste, want je zit er snel door, in de plastiekjes die het koper van de draad omhullen en dat wil je niet!
Wanneer het witte plastiek verwijderd is, moet je ook nog een stukje van de plastiekjes die het koper omhullen verwijderen.
Schuif nu het elektrische snoer door de trekontlaster en de moer (maak de moer al vast op de trektonlaster) en schuif het hierna door de opening van de fitting. Vervolgens maak je de twee koperen draadje vast op de contactplaatjes van de fitting door ze vast te zetten met de schroefje in de fitting. De kant met de vijsjes moet naar boven!
Wanneer je snoer met je fitting verbonden is, moet je enkel nog het cilindervormige stuk op je fitting schroeven. Schroef er ook het deksel van de fitting op voor je probeert om de fitting in het deksel van de bokaal te steken. Ervaring heeft mij geleerd dat de fitting er niet gemakkelijk weer uit komt!
Hierna moet je enkel nog je deksel van je fitting naar beneden schroeven en je bent klaar met het eerste deel van je lamp!
De schakelaar aan de bokaallamp bevestigen
De schakelaar is zowat het enige stuk waar je fouten kan maken op gebied van elektrische stroom. Ik slaagde er de eerste keer wel in om mijn fitting verkeerd aan mijn draad te hangen, waardoor ik ook kortsluiting had, maar dat zal wel een uitzondering geweest zijn.
Begin met de schakelaar open te schroeven en alle stukje los te schroeven. Zorg dat je geen vijsje kwijt speelt. Bepaal waar je schakelaar moet komen in je draad (het is nooit een slecht idee om uw lamp + draad mee te nemen naar de plaats waar je ze wilt zetten en daar te kijken wat de ideale hoogte voor de schakelaar is). Knip hem daar in twee. Strip het snoer aan beide kanten.
Plaats het snoer in de schakelaar. Let nu op, want de draadjes moeten op de juiste manier aan elkaar passen. In dit geval: bruin bij bruin en blauw bij blauw. Schroef de vijsjes naar beneden zodat de koperdraad geklemd zit. Monteer de schakelaar daarna weer.
De stekker bevestigen
De stekken bevestig je op een gelijkaardige manier als de fitting en de schakelaar. Hoe precies hangt af van het type stekker. Ik had een heel simpel model waarbij ik mijn draad in het “bekje” van de stekker moest leggen en de twee koperen draadjes in twee kleine buisjes moest steken. Daarna hoefde ik de stekker gewoon toe te duwen en het omhulsel ervoor te schuiven. Klaas was kees!
En dan is het tijd om je bokaallamp te testen! Een klein beetje spannend, maar wanneer de lamp gaat branden, is het gelukt!
Ik maakte een kleine en een grote lamp en hoewel ik ze eigenlijk super cool vind, zo naast elkaar, gaat de kleine op de boekenplank blijven wonen en komt de grote naaste onze zetel te hangen, zodat ik daar een leeslamp heb. Daarom ook dat ik die extra treklontlaster kocht, want zo kan ik de lamp gemakkelijk aan het plafond ophangen.
Wat vind je van mijn bokaallampjes? Ga je ze zelf maken?
5 Comments
Yes, merci Eline! Ik ga proberen goedkope mason jars te scoren en dan eens aan de slag! Gelukkig kan ik voor de electriciteit ook bij mijn papa terecht, want zelf ben ik toch een beetje een kneusje als het daarop aankomt! Ziet er alleszins super mooi uit op uw plankje! (En als leeslamp, hoe tof!)
super leuk! misschien ook eens proberen
Mooi, zeg! Zo samen zien ze er anders echt heel stijlvol uit! Misschien moet je er nog een paar bijmaken…
[…] Zelf een meubel maken (DIY Jar Lamp) […]
[…] to the everlasting ‘projects I want to do someday’-list. When I started planning my mason jar lamp tutorial, I knew I finally could give the desk lamp a second […]